Plumbing for Beginners: The Essentials for Installing a Bathtub
Plumbing for Beginners: The Essentials for Installing a Bathtub
Blog Article
Were you interested in information and facts around How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Mounting a tub isn't specifically brain surgery, however it does need strong plumbing, woodworking, and sometimes, tiling abilities. Replacing an old bath tub with a brand-new one is also a reasonably hard job. If the old bathtub is readily available, the task can move speedily; if you have to open up a wall to eliminate the old bathtub and also position the brand-new bath tub, the task is much harder. In either case, the project is within a home handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and set in the brand-new one. Ensure you have certified on your own for the work and fit attempting it. As opposed to working with a professional to take over a halfway-completed project, it is better to think about utilizing one before you begin. Possibilities are you might need a professional plumber to make tube links.
This write-up will assist you install a new bathtub in your restroom if you have already gotten a brand-new bathtub as well as do not require to transform the setup of your previous supply of water pipes.
Your tools and product checklist must make up the following:
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installation, then the first thing you need to do is detach the water. After doing so, activate the taps to drain pipes any type of water remaining in the system. The process of getting rid of the existing faucets can be quite troublesome as a result of the limited access that is often the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the taps. Have a towel prepared for the continuing to be water that will come from the pipes. As soon as the supply pipes have actually been gotten rid of, use the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from transforming during this process. When the faucets have actually been removed, the holes in the bath/basin will have to be cleansed of any kind of old sealing substance.
Prior to proceeding to fit the new faucets, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the brand-new taps to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the thread. One end of the connector fits on the plastic tail of the tap as well as the various other end gives a link to the existing supply pipes.
If you require to fit a monobloc, after that you will call for minimizing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the installing hole in the bath/basin making certain that the washers are in location in between the tap and also the sink. Protect the faucet in place with the supplier offered backnut. As soon as the faucet is securely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with normal tap ports. The former kind should be linked to the faucet finishes initially, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.
Installing the Tub
Making use of both wood boards under its feet, position the tub in the needed placement. The wood boards are helpful in evenly spreading the weight of the bathtub over the location of the boards instead of focusing all the weight onto four little points.
The next goal is to ensure that the bathtub is leveled all round. This can be achieved by inspecting the spirit level and readjusting the feet on the tub up until the spirit level checks out degree.
To install taps, fit the bottom of the outermost adaptable faucet connector to the ideal supply pipeline by making a compression sign up with; then do the exact same for the various other faucet.
Turn on the water supply as well as inspect all joints as well as brand-new pipework for leaks and also tighten them if essential. Fill up the bathtub and likewise inspect the overflow outlet and also the regular electrical outlet for leaks.
Lastly, repair the bath paneling as explained in the maker's instruction manual. Tiling as well as securing around the tub must wait up until the bathtub has actually been made use of at the very least when as this will settle it right into its final placement.
Preparing for the Setup
To start with, the sustaining framework supplied with the bathroom must be fitted (if needed) according to the maker's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to see to it that if the tap features a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps unit to avoid stress on the tub.
Fit the versatile tap connectors to the bottom of both faucets making use of 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet through the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make certain you use every one of the supplied washers.
Link the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bath must now be ready to be suited its last position.
Tiling Around the Bathtub
In the area where the bathroom satisfies the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to fracture a stiff seal, causing the water to penetrate the wall between the bathroom and also the tiling, causing problems with wetness and also feasible leakages to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes and also cartridges, and can securing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill up the bathtub with water prior to securing, to allow for the movement experienced when the bathtub is in use. The sealer can break rather very early if you do not take into consideration this movement before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also easily available on the market. It is suggested to fit the ceramic tiles using waterproof or water-proof sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
I hope you enjoyed reading our post about Installing A Bathtub. Thanks a lot for finding the time to read through our blog post. Sharing is nice. Helping others is fun. Thanks so much for your time spent reading it.
Top-rated emergency plumbing? Connect today. Report this page